Vacuuming is the easiest and most effective way to keep your carpet clean. Regular vacuuming can also have the largest impact on the air you breathe. Auckland Carpet Cleaning will present all sorts of guidelines for cleaning, removing stains, and dealing with various problems.

For now, though, we’ll get to the basics:

Carpets need to be vacuumed cleaned once a week and more often in areas of heavy traffic. Frequent vacuuming prolongs the life of your carpets. Generally, by preventing a buildup of gritty particles that can cut carpets fibers. Every few weeks, take a little extra time and use your crevice tool for cleaning around baseboards and radiators. As well as hard to reach places.

To vacuum clean wall to wall carpeting, divide the floor into quadrants and vacuum an entire quadrant before moving on to the next. Take your time when you vacuum clean carpets. Specially plush carpets in which dirt is sure to be deeply embedded. One pass with a high-powered upright is not enough. Go over each section of carpeting several times. Then work slowly to allow the suction to remove all the ground in dust and dirt. Pay special attention to the areas where people sit and move their feet. Vacuum these areas of heavy traffic with a crisscross pattern of overlapping strokes. Soil retardants can be applied to new carpets or to newly cleaned carpets. Follow manufacturers’ advice. Apply soil retardants only with professional equipment using the recommended application techniques. Add baking soda to the bag in your vacuum to fight odors.

Odors are one thing, spots and spills are quite another. This happen to just about every carpet and can be difficult to remove. In the next section, we’ll offer some pointers for getting rid of those blemishes.

Carpet Cleaning Spots and Spills

Here’s Rule No. 1 regarding spots and spills on your carpeting, clean them immediately. If you catch the spill when it’s fresh, you’ve got a good chance of removing it totally.

Consider these tips, too. Carefully blot or scrape the entire area before applying any carpet cleaning solution. Remove as much of the spill as possible. Before using any carpet cleaning solution, test the cleaning agents that you keep on hand before you have to use them. Surely to make sure they will not harm your carpet. Do not rub the spill that might spread the problem to a larger area. When you apply carpet cleaning spot cleaner, work from the outside of the stain toward the inside to avoid spreading the stain. After applying a carpet cleaning solution, blot up all the moisture.

A clean white bath towel is unsurpassed for drying carpet and brushing the nap back up to a standing position. If you feel that there is still too much moisture after blotting the carpet, place a 3/4-inch-thick stack of white towels. What should you do if your carpet is soiled? In the next section, we at Auckland Carpet cleaning will provide answers to these and other questions.

Treating Specific Carpet Stains

From wine to chewing gum, your carpeting has a lot of potential enemies. In this section, we’ll tell you how to remove a variety of specific carpet stains.

Chewing gum

Chewing gum can be a sticky mess. At any rate, harden it by pressing an ice cube against the blob of gum. Once hardened, the gum can be pulled off the carpet.

Chocolate

Immediately scrape the chocolate from the carpet. Mix 1 teaspoon mild detergent and 1 teaspoon white vinegar. Then add 1 quart warm water. Apply the solution to the spot. Rinse well. Vacuum.

Coffee

Blot spilled coffee immediately from carpets. Then mix 1 teaspoon mild detergent,1 teaspoon white vinegar, and 1 quart warm water. Apply the cleaning solution to the spot and let dry. Apply dry-cleaning fluid. Vacuum gently after the carpets is dry.

Acid stains

Acid spills, such as drain cleaner or vinegar, demand quick action. Dilute them immediately with baking soda and water or with club soda. Then apply a solution of ammonia (1 part) and water (10 parts). Rinse with cold water, let dry, and vacuum gently.

Alcoholic beverages

Quickly dilute the spot with cold water. Absorb the excess liquid. Then mix 1 teaspoon mild detergent, 1 teaspoon white vinegar, and 1 quart warm water. Apply the solution to the spot, and let the carpets dry. Vacuum gently.

Blood

Absorb as much of the blood as you can. Then mix 1 teaspoon mild detergent, 1 teaspoon white vinegar, and 1 quart warm water. Apply the solution to the spot, and let dry. Apply dry-cleaning fluid. Vacuum gently after the carpets is dry.

Butter

Scrape up as much of the butter as you can. Apply dry-cleaning fluid, and let the carpets dry. If the spot remains, repeat the procedure. Vacuum gently.

Candle wax

Press an ice cube against the wax stain. The wax will harden and can then be pulled off.

Urine

Mix 1 teaspoon mild detergent, 1 teaspoon white vinegar, and 1 quart warm water. Apply the solution to the spot. Let the carpets dry. If the spot remains, repeat the procedure. Vacuum carpets.

Vomit

Treat vomit quickly. Blot up as much as possible off the carpets then dilute immediately with baking soda. Add water or with club soda. Apply a cleaning solution of 1 part ammonia and 10 parts water. Rinse with cold water, let carpets dry, and then vacuum clean.

Wine

When red wine is spilled on your carpets, dilute it with white wine. Then clean the spot with cold water and cover with table salt. Wait ten minutes, then vacuum up the salt. When nothing seems to work, you may want to try a deep- carpets cleaning.

Catsup

Sponge a mixture of 1 cup vinegar and 2 cups water into rug. Frequently wring out sponge until stain is gone.

Crayon

Scrape away excess crayon or remove it by placing a blotter over the crayon stain. By pressing the carpets with a warm iron until the blotter absorbs the melted crayon. Move the blotter frequently so that it doesn’t get over saturated. Apply dry-cleaning fluid, and let the carpets dry. Vacuum gently.

Fruit

Fruit stains can be very hard to remove from carpets if they are allowed to set. On the contrary, if you act quickly this method usually prevents a permanent stain. Scrape up spilled fruit, and absorb fruit juice. Mix 1 teaspoon mild detergent, 1 teaspoon white vinegar, and 1 quart warm water. Apply the cleaning solution to the spot, and let the carpet dry. If the spot remains, repeat the procedure. Vacuum gently.

Gravy

Wipe up as much of the spilled gravy from carpets as possible. Mix 1 teaspoon mild detergent, 1 teaspoon white vinegar, and 1 quart warm water. Apply the cleaning solution to the spot. Let the carpet dry. Apply dry-cleaning fluid, and let the carpet dry. Vacuum.

Mud

Allow the mud to dry completely and then brush or scrape off as much as possible from the carpets. Mix 1 teaspoon mild detergent, 1 teaspoon white vinegar, and 1 quart warm water. Apply the cleaning solution to the stain spot. Let the carpets dry. If the stain remains, apply dry-cleaning fluid and blot dry. When the spot is completely dry, vacuum gently carpets.

Salad dressing

Absorb as much salad dressing as you can from your carpet. Mix 1 teaspoon mild detergent, 1 teaspoon white vinegar, and 1 quart warm water. Apply the cleaning solution to the spot. Let the carpets dry. If the spot remains, repeat the procedure. Vacuum carpets gently.

Soft drinks

The carbonation in soft drinks will help you clean spilled drinks quickly. Act fast because some of the dyes in the drinks can permanently stain your carpet. Blot up the spilled drink. Mix 1 teaspoon mild detergent, 1 teaspoon white vinegar, and 1 quart warm water. Apply the solution to the spot. Let the carpets dry. If the spot remains, repeat the procedure. Vacuum carpets gently.

Deep Cleaning Carpets

There comes a time in the life of every carpets when vacuuming can no longer restore its clean appearance. There are four major indicators of the need for a deep carpet cleaning job:

  • Carpet is matted and feels sticky.
  • The carpets is no longer the same color as the remnant you saved when the carpets was new.
  • Has grimy circles around the chairs.
  • Releases a dust storm when you run across the room.

If any of these descriptions fit your carpet, then it is time to deep carpet clean it. Unless you have the time and strength to do a thorough carpet cleaning job, it’s time to call in the professionals. The only method for carpet cleaning or to clean carpeting down to the backing is to rinse with an steam cleaning extractor.

Here’s how it’s done:

Before cleaning your carpets, test for colorfastness. Moisten a white towel with the carpet cleaning solution that you are going to use. Apply it to an inconspicuous area. If the towel does not pick up any color from the carpets, it is probably safe to use the solution on the entire carpets.

Procedure

Remove as much furniture from the room as possible. Place foil or plastic film under the legs and bases of the remaining furniture to prevent carpet stains. Vacuum clean the carpets thoroughly. In addition, spot-clean and pre treat stains before steam cleaning the carpet. Follow the instructions printed on the carpet cleaner.

Use single strokes over the carpet surface. Do not apply heavy pressure with the carpet clean wand. Wipe cleaning solutions, foam from furniture legs, and woodwork immediately to prevent damage. Fluff damp fibers against the nap after carpet cleaning to aid drying. Make sure the room is well ventilated after carpet cleaning to speed drying. Try not to walk on carpets until they are dry. Onward to Auckland Carpet Cleanings final section, where we’ll tell you how to treat special types of carpet problems.  To explain burned areas and loose threads.

Special Carpet Stain Removal

Auckland Carpet CleaningWhen your carpet is burned, stained, or discolored, you could simply move a big chair over the spot and forget about it. You can use one of the following simple methods to restore your carpet to its original good looks. If the spot remover carpet cleaner you use alters the color of your carpet, try touching up small places with artists’ acrylic paint. If acrylic paint doesn’t work, try using a felt-tip marker of the appropriate color. Go slowly, and blend the color into the fibers.

To raise depressions left in a carpet by heavy furniture, try steam cleaning or hold a steam iron. Specifically close enough for steam to reach the carpet, or on a damp towel. Don’t let the iron touch the carpet fibers, especially if the carpet is synthetic. This because they could melt. Lift the carpet fibers by scraping them with the edge of a coin or spoon. If a carpet thread is loose, snip it level with the pile. If you try to pull out the thread, you risk unraveling part of the carpet.

Carpet Burn Tip

To repair a large carpet burn, cut out the damaged area of carpet and substitute a patch of identical size and shape. Secure the new piece of carpeting with double-sided carpet tape or professional heat bond. To repair a small area burned down to the carpet backing, snip off the charred fibers and put white glue in the opening. Then snip fibers from a scrap of carpet or an inconspicuous part of the carpet (perhaps in a closet). When the glue gets tacky, poke the carpet fibers into place. If the burn isn’t all the way down to the backing, just use sandpaper or snip off the charred tips of the fibers with scissors. The slightly shorter length of a few carpet fibers will never be noticed.

Consumer Carpet Cleaning Services and Rug Cleaning Tips

Here you can learn about different carpet cleaning services and ask any question you have about carpet cleaning or rugs. You can learn how to choose a carpet cleaning service or get information about cleaning rugs yourself with our tips in our blog. We welcome your questions, and we are sure you will find the answers you have been looking for.

Carpet and rug cleaning, comes in a variety of methods. Each method has their strengths and weaknesses. The Carpet and Rug Institute, recommends hot water extraction (steam cleaning) as the preferred method. This method is preferred if you have have pets, allergies, kids, or adults who wear shoes inside the house. In order to benefit from hot water extraction, you need at least 180 degrees temperature, at the carpet when cleaning. This means, the supply of hot water must be hotter than 180 to compensate for the drop in temperature between the source and the end of the cleaning tool used. The only way this can be achieved efficiently is by a professional carpet cleaning company with a truck mounted extractor.

Portable heaters

There are heated portables on the market that consumers can buy, but there is a trade off in extraction performance, for the heat, and the heat cannot maintain 180 degrees at the carpet. The temperature of 180 degrees is important, because this temperature sanitizes the carpet by killing bacteria, fleas, and dust mites. If you do not have allergies, pets, kids, wear shoes inside, and you frequently vacuum, then you are a perfect candidate for low moister carpet cleaning. This method can be accomplished in different fashions, by spreading a moist spongy material on the carpet (HOST), or spraying an encapsulation product, or a cleaner on the carpet. The method to recover it is similar with a rotary pad machine that rubs the carpet of the dirt and spray, giving the appearance of clean carpet. This method is really a surface cleaner, and the results do look good, if you have light soiling.

When it comes to rug cleaning, it depends on the quality and where it was made, when determining the preferred carpet cleaning method. If your rug is hand made then the method recommended by respected professionals is a full submerged bath and rinse. This process is typically done by a rug specialist, who has a “rug pit” at their place of business, and is skilled in knowing the fabric, and make of the rug, in order to know how to proceed with care.

Carpet Cleaning Companies

Companies like Auckland Steam ‘n’ Dry  and other professional carpet cleaning companies have facilities like this to rid the rug of any odors, fine particles, and it thoroughly cleans the rug. This process usually costs by square foot of the rug and you can take the rug to the shop, or the professional will pick it up for you.If your rug is a machine wool,  it depends on you if you want to take it to a professional. You will still get a thorough cleaning, but the price could be close to what you paid for it. Some people do not mind, because the design of the rug, matches the decoration of the house, and that rug cannot be found again. But, if your rug is a synthetic rug that looks like carpet, then you can probably clean it yourself or have a professional carpet cleaner, clean it at your home. This all depends on the same factors as mentioned above.

Areas Serviced

South Auckland, East Auckland, West Auckland, North Shore Auckland, Eastern Bays, Eastern Suburbs, Western Suburbs, Manukau City, Waitakere City, Cbd, North Shore, Shore, Waitakere, Manukau, Howick, Pakaranga, Botany, Panmure, Ellerslie, Mt Wellington, Penrose, Greenlane, Remuera, Newmarket, Epsom, Mt Roskill, Mt Albert, Manurewa, Botany, East Tamaki, Otara, Dannemora, Otahuhu, Onehunga, Papatoetoe, Pukekohe, Papakura, Mangere, Manerewa, Parnel, City, Hernebay, Ponsonby, Pt Chev, New Lynn, Henderson, Te Atatu South, Te Atatu Penisula, Auckland City, North Shore, Glendene, Glen Eden, Titirangi, Massey, Greenhieth, West Habour, Hobsonville, Orewa, Brownsbay, North Shore, Glenfield, Birkdale, Birkenhead, Takapuna , North Habour, North Auckland, Devonport, Milford, East Coast Bays, Hibiscus Coast, Whangaparoa, Rodney District, Albany, Nth Shore, Auckland Cbd, Manukau City